Generic selectors
Exact matches only
Search in title
Search in content

Six leaking agitators find a permanent sealing solution with the Inpro/Seal® Air Mizer®

Inpro-Seal

Six leaking agitators find a permanent sealing solution with the Inpro/Seal® Air Mizer®

The Domtar Nekoosa pulp and paper mill, founded in 1883 as the Nekoosa Paper Company, has been operating along the banks of the Wisconsin River for more than 130 years.  The facility is an integrated mill, producing pulp and publishing grade paper.  Annual paper production capacity is 118,000 tons, and an annual pulp production is 155,000 tons.  

The facilities management team, consisting of Tom Appel, Maintenance/Engineering Manager; Jim Love, Paper Mill Maintenance Planner; Dan Savage, Paper Mill Maintenance Supervisor; Gary Krings, Pulp Mill Maintenance Planner and Tom Hintz, Pulp Mill Maintenance Supervisor, continually seeks ways to improve the reliability and performance of key equipment at the mill. In an era of tough competition and closing paper mills, this approach has contributed to the mill’s continued success.  

Costs and Concerns Spur Change

Inpro-Seal Slurry TankSix side entry agitators were used in critical applications in the pulp and paper making process as they continuously mixed product in the tanks to prevent solids from settling to the bottom. Shaft deflection and misalignment, a common problem in most side entry agitators, made effective shaft sealing impossible on these units. Unreliable shaft seals lead to product leakage and contribute to premature bearing failure, causing an increase in unscheduled downtime, expensive maintenance repairs and costly product loss.

Two of the tanks located outdoors contain white liquor, a hot, corrosive and hazardous by-product of paper pulp production. One agitator was sealed with a double mechanical seal with a conventional glycol seal pot support system. The other agitator was sealed with conventional packing. When white liquor leaked through the seal, it was not only a maintenance issue but also an environmental concern.

The other four agitators were located on tanks inside the mill. These tanks held abrasive ground Calcium Carbonate and Filler Clay slurries.  Because the slurries are abrasive, wear to the shafts and packing was excessive.  This led to frequent re-packs, unnecessary maintenance and significant product loss to the drain.   Flushing the packing with clean water would delay the breakdown, but wasn’t acceptable due to dilution of the product in the tanks.

Annual costs for maintenance and lost product on these six agitators at the mill averaged over $82,000. The maintenance team recognized it was time to investigate new sealing options to improve performance and reduce costs.

In late 2005, the Maintenance Management Team met with Chuck Kimball, President of M.R.O. TECH, Inc., a local, long time Inpro/Seal distributor, to discuss options for upgrading the sealing method used on these agitators. Kimball recognized the side-entry agitators on the large tanks were an ideal application for the Inpro/Seal Air Mizer®. The maintenance team was eager to try the new sealing technology. “The team’s innovative/early adopter culture makes it very gratifying to work with them and find solutions to troublesome applications, such as these agitators” stated Kimball.

The Inpro/Seal Air Mizer Solution

The Inpro/Seal Air Mizer product seal is a non-wearing, permanent shaft seal that uses a positive purge to create an effective seal, preventing product or harmful emissions from escaping into the atmosphere. It seals by directing small amounts of air, inert gas or water through a precision clearance between the throttle and shaft, pressurizing the clearance. The sealing medium is evenly dispersed around the shaft to prevent dead spots and is directed toward the product and atmosphere evenly to safeguard against both product loss and contamination.

Unlike traditional seals, the Air Mizer fully articulates to accommodate shaft deflection, run-out and misalignment and does not require periodic adjustments. Its unique non-contacting design does not wear out or groove the shaft, therefore, providing a permanent sealing solution. All Air Mizers are custom engineered to fit the application, and provide an effective shaft seal for powders, liquids, slurries and bulk solids.

Upfront Costs Yield Quick Savings

Kimball explained to Tom Hintz the operating principle and technology of the Air Mizer and the performance up-grade to be expected. The decision was made to proceed.

In December 2005, a split custom engineered stainless steel Air Mizer was installed on one of the white liquor tank agitators. It proved to be the perfect solution for their leaking agitators. Other installations followed in rapid succession – the second white liquor tank agitator in Aug 2006, and the indoor slurry agitators in 2006, 2007 and 2008. With the exception of a frozen air line 5-years ago, the two white liquor seals have run trouble-free for 8-years. The first two clay slurry seals installed in 2006 have operated leak-free continuously since initial installation.

Hintz said “The split designs made installation quick and easy. No modifications to the agitators were required and there is no on-going maintenance with the seals other than maintaining a low pressure air purge.”

By switching to Air Mizers, the Nekoosa mill has realized impressive savings. After initial and continuous air costs, the Air Mizers installed are saving the mill:

  • $23,000 per year on the two white liquor tank agitators.
  • $51,000 per year on the four calcium carbonate and filler clay tank agitators.

Because the cost of the new seals consisted mainly of up-front, one-time expenditures, the team expects the $74,000 savings per year to continue. A significant portion of this saving is the elimination of product loss. “Installing Air Mizers on our side entry agitators has proven to be a tremendous success. These seals paid for themselves within the first year of operation and we look forward to continued cost savings for many years to come.” Stated Love.

Click here to Download Case Studies

About Inpro/Seal

The inventor of the original Bearing Isolator, Inpro/Seal® has been delivering innovative sealing solutions and outstanding customer service for more than 30 years. Their unique technologies increase the reliability of rotating equipment and provide real cost savings by improving the mean time between repair (MTBR). Inpro/Seal’s superior customer service and streamlined production processes allow for same or next-day shipments on most products, even new designs. Headquartered in Rock Island, Ill., USA, Inpro/Seal maintains a global sales and distribution network to provide responsive, localized support to customers worldwide and manufactures in North America, South America, Asia and Europe. Inpro/Seal is a Waukesha Bearings® business. Waukesha Bearings is an operating company of Dover. Additional information is available at www.inpro-seal.com.

Related Articles

Related Whitepapers

Overcoming Clean-In-Place Challenges in Hygienic Applications with Mouvex® H-FLO Series Pumps

Clean-In-Place (CIP) Challenges There are numerous challenges that must be overcome when cleaning a hygienic pump installation. This is especially true when using a clean-in-place…

Power Transmission Solutions for Hydraulic Fracturing Applications

Altra Industrial Motion provides advanced power transmission solutions for hydraulic fracturing applications. The well-recognized brands of Altra Industrial Motion supply technically advanced universal joints, couplings,…

Evolution of Pumping Technology and Superior Performance

This document begins with a history of the development of variable speed technology, explaining the efficiency improvements associated with each development step. Also presented is…

Engine & Turbine Manufacturer Achives Annual Savings of $245,000 [Case Study]

Find out how Grundfos iSOLUTIONS delivered significant energy savings and system optimizations for a leading engine and turbine manufacturer. A leading UK engine and turbine…

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community


By submitting this form, you are consenting to receive marketing emails from: raybet & raybet 雷竞技 , 2205-C 7th Street, Tuscaloosa, AL, 35401, //www.stokoptom.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact